Cobra CT6 Specifications download pdf (Page 7)

NOTE:

The gas pressure regulator provided with this

appliance is convertible between Natural Gas and

LPG as per the ‘Gas Conversion Section’ in this

manual.

Ensure the regulator is converted to the correct gas

type that the appliance will operate on.

The regulator outlet pressure is fixed ex-factory for

the gas type that the regulator is converted to and it

is NOT to be adjusted

The regulator connections are

" BSP female.

The connection to the appliance is

" BSP male.

(Refer to the ‘Specifications’ section for the gas

supply location dimensions).

NOTE:

A Manual Isolation Valve must be fitted to the

individual appliance supply line.

4. Correctly locate the appliance into its final

operating position and using a spirit level, adjust

the legs so that the unit is level and at the

correct height.

5. Connect the gas supply to the appliance. A

suitable joining compound which resists the

breakdown action of LPG must be used on every

gas line connection, unless compression fittings

are used.

6. Check all gas connections for leakages using

soapy water or other gas detecting equipment.

7. Check that the gas supply pressure is as shown in

the Specifications section, ‘Gas Supply

Requirements’ tables.

NOTE:

The supply pressure to be measured at the

manifold test point.

8. Light the Main Burners. Refer to the 'Operations’

Section', ‘Using the Griddle’ / ‘Using the Toaster’.

9. Verify that the supply pressure is still correct.

10. Check that the Main Burner is alight and adjust

the low fire adjustment screw on the open

burner gas control valves to obtain the desired

flame size.

11. Check / adjust the main burner aeration gap.

This gap should be set to the dimensions shown

in the 'Gas Specification Tables' in ‘Part 6 - Gas

Conversion’, ‘Gas Specifications’ tables.

Part 3 Installation

Assembly

This model is delivered completely assembled.

Ensure that the legs are securely attached.

NOTE:

This appliance is fitted with adjustable feet to enable

the appliance to be positioned securely and level.

This should be carried out on completion of the gas

connection. Refer to the 'Gas Connection' section.

Gas Connection

NOTE:

ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A

QUALIFIED SERVICE PERSON.

1. Cobra Series Gas Griddle Toasters do not require

an electrical connection, they function totally on

the gas supply only.

2. It is essential that the gas supply is correct for the

appliance to be installed and that adequate

supply pressure and volume are available. The

following checks should be made before

installation:-

a. The Gas Type the appliance has been

supplied for is shown on coloured stickers

located above the gas entry point and next

to the rating plate. Check that this is correct

for the gas supply the appliance is being

installed for. The gas conversion procedure is

detailed in the Gas Conversion Instruction

Sheet for this appliance.

b. Supply Pressure required for this appliance is

shown in the ‘Specifications’ section of this

manual. Check the gas supply to ensure that

adequate supply pressure exists.

c. Input Rate of this appliance is also stated on

the Rating Plate fitted to the inside of the right

hand side panel, below the middle shelf and

in the ‘Specifications’ section of this manual.

The input rate should be checked against the

available gas supply line capacity. Particular

note should be taken if the appliance is being

added to an existing installation.

NOTE:

It is important that adequately sized piping runs

directly to the connection joint on the appliance,

with as few tees and elbows as possible to give

maximum supply volume.

3. Fit the gas regulator supplied, into the gas supply

line as close to the appliance as possible.

WARNING:

DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES.

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Comments to this Manuals

No comments

Cobra CT6 Specifications Page 7

Comments to this Manuals